系统备份异常

[jugg]

新刷的0613的系统

然后用U盘备份

开机后就出现内核崩溃

不接备份U盘 能正常进系统

Connecting to COM4...
Connected.

¿ÿ񁀿ÿÿDDR V1.09 a930779e06 typ 22/11/21-17:50:56
LPDDR4X, 2112MHz
channel[0] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[1] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[2] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[3] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
Manufacturer ID:0xff
CH0 RX Vref:30.7%, TX Vref:21.8%,21.8%
CH1 RX Vref:30.7%, TX Vref:21.8%,21.8%
CH2 RX Vref:28.7%, TX Vref:21.8%,21.8%
CH3 RX Vref:29.7%, TX Vref:22.8%,20.8%
change to F1: 528MHz
change to F2: 1068MHz
change to F3: 1560MHz
change to F0: 2112MHz
out
INFO:    Preloader serial: 2
NOTICE:  BL31: v2.3():v2.3-557-g9609b9c19:derrick.huang
NOTICE:  BL31: Built : 14:29:57, Mar  8 2023
INFO:    spec: 0x13
INFO:    ext 32k is not valid
INFO:    ddr: stride-en 4CH
INFO:    GICv3 without legacy support detected.
INFO:    ARM GICv3 driver initialized in EL3
INFO:    valid_cpu_msk=0xff bcore0_rst = 0x0, bcore1_rst = 0x0
INFO:    system boots from cpu-hwid-0
INFO:    idle_st=0x21fff, pd_st=0x11fff9, repair_st=0xfff70001
INFO:    dfs DDR fsp_params[0].freq_mhz= 2112MHz
INFO:    dfs DDR fsp_params[1].freq_mhz= 528MHz
INFO:    dfs DDR fsp_params[2].freq_mhz= 1068MHz
INFO:    dfs DDR fsp_params[3].freq_mhz= 1560MHz
INFO:    BL31: Initialising Exception Handling Framework
INFO:    BL31: Initializing runtime services
INFO:    BL31: Initializing BL32
I/TC: 
I/TC: OP-TEE version: 3.13.0-652-g4542e1efd #derrick.huang (gcc version 10.2.1 20201103 (GNU Toolchain for the A-profile Architecture 10.2-2020.11 (arm-10.16))) #5 2022年 09月 20日 星期二 09:41:09 CST aarch64
I/TC: Primary CPU initializing
I/TC: Primary CPU switching to normal world boot
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0x200000
INFO:    SPSR = 0x3c9


COOLPI LOADER BY YANYI(Jun 06 2023)

DRAM:  8 GiB
Using default environment

switch to partitions #0, OK
mmc0(part 0) is current device
reading logo.bmp
FAT: Misaligned buffer address (00000000ebc9e610)
switch to partitions #0, OK
mmc0(part 0) is current device
reading logo.bmp
0 2 1 3 6 8 7 9 Monitor has basic audio support
hdmi info isn't saved in main block
mode:1920x1080 bus_format:0x100a
hdmi@fde80000:  detailed mode clock 148500 kHz, flags[5]
    H: 1920 2008 2052 2200
    V: 1080 1084 1089 1125
bus_format: 100a
VOP update mode to: 1920x1080p0, type: HDMI0 for VP0
dclk:148500,if_pixclk_div;2,if_dclk_div:4
rockchip_vop2_init: hdmi1_phy_pll may not define
hdptx_ropll_cmn_config bus_width:16a8c8 rate:1485000
hdptx phy pll locked!
VP0 set crtc_clock to 1485KHz
VOP VP0 enable Esmart0[1920x1080->1920x1080@0x0] fmt[1] addr[0xee4ef000]
CEA mode used vic=16
mtmdsclock:148500000
bus_width:0x16a8c8,bit_rate:1485000
hdptx phy lane locked!
dw_hdmi_setup HDMI mode
don't use dsc mode
dw hdmi qp use tmds mode
boot mode: None
Autoboot in 1 seconds
VOP VP0 enable Esmart0[1920x1080->1920x1080@0x0] fmt[1] addr[0xee4ef000]
starting USB...
Bus usb@fc000000: usb maximum-speed not found
trsv ln0 mon rx cdr lock timeout
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
Bus usb@fc880000: USB EHCI 1.00
Bus usb@fcd00000: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fc000000 for devices... 1 USB Device(s) found
scanning bus usb@fc880000 for devices... 2 USB Device(s) found
scanning bus usb@fcd00000 for devices... 1 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found

Device 0: Vendor: Generic  Rev: 8.07 Prod: Flash Disk      
            Type: Removable Hard Disk
            Capacity: 30000.0 MB = 29.2 GB (61440000 x 512)
... is now current device
Scanning usb 0:1...
Found /extlinux/extlinux.conf
Retrieving file: /extlinux/extlinux.conf
reading /extlinux/extlinux.conf
274 bytes read in 35 ms (6.8 KiB/s)
1:	Linux coolpi
Retrieving file: /initrd.img
reading /initrd.img
8202961 bytes read in 796 ms (9.8 MiB/s)
Retrieving file: /Image
reading /Image
37706240 bytes read in 3647 ms (9.9 MiB/s)
append: root=LABEL=writable rw rootfstype=ext4 console=tty0 quiet splash plymouth.ignore-serial-consoles vt.global_cursor_default=1 irqchip.gicv3_pseudo_nmi=0 net.ifnames=0 rtleth=ethaddr:96:39:8b:af:40:ae
Retrieving file: /rk3588s-cp4.dtb
reading /rk3588s-cp4.dtb
141838 bytes read in 46 ms (2.9 MiB/s)
## Flattened Device Tree blob at 0x0a100000
   Booting using the fdt blob at 0x0a100000
   Loading Ramdisk to eb201000, end eb9d3ad1 ... OK
   Loading Device Tree to 00000000eb1db000, end 00000000eb200a0d ... OK
switch to partitions #0, OK
mmc0(part 0) is current device
reading logo_kernel.bmp
FAT: Misaligned buffer address (00000000ebcb6950)
switch to partitions #0, OK
mmc0(part 0) is current device
reading logo_kernel.bmp
Adding bank: 0x00200000 - 0x08400000 (size: 0x08200000)
Adding bank: 0x09400000 - 0xf0000000 (size: 0xe6c00000)
Adding bank: 0x100000000 - 0x200000000 (size: 0x100000000)
Adding bank: 0x2f0000000 - 0x300000000 (size: 0x10000000)

Starting kernel ...

I/TC: Secondary CPU 4 initializing
I/TC: Secondary CPU 4 switching to normal world boot
I/TC: Secondary CPU 5 initializing
I/TC: Secondary CPU 5 switching to normal world boot
I/TC: Secondary CPU 6 initializing
I/TC: Secondary CPU 6 switching to normal world boot
I/TC: Secondary CPU 7 initializing
I/TC: Secondary CPU 7 switching to normal world boot
I/TC: Secondary CPU 1 initializing
I/TC: Secondary CPU 1 switching to normal world boot
I/TC: Secondary CPU 2 initializing
I/TC: Secondary CPU 2 switching to normal world boot
I/TC: Secondary CPU 3 initializing
I/TC: Secondary CPU 3 switching to normal world boo

就卡在这里不动了
显示器上面是内核崩溃一样的信息打印

[jugg]

这个备份U盘之前备份过之前旧的系统 可以备份 可以还原 就这个不行

[jack_admin]

@jugg 哪个板子？看log是4b u盘

[jugg]

@jack_admin
是4B 用U盘备份
U盘的内容我没动过 备份几次之后就这样了
把U盘重新刷了 又能备份了

[jugg]

@jack_admin

这里最近的就是0306的
现在0613的备份 能不能用这个来还原

[大法师]

@jugg 看iso名称，install是安装系统用的。备份使用backup iso